Home » Product Info »
COV1802

CoverLite Syn Tissue Orange 19.5" x 36"

Product Info
COVERITE

COV1802
CoverLite Syn Tissue Orange 19.5" x 36"
By COVERITE
Discontinued
No Picture Available

More like this... Tissue Aircraft Covering
But only from... COVERITE
All items from... COVERITE


 Inventory Status Legend
StockStock availability for on-line ordering
0
$8.99
Warehouse ?
StockStock availability for pick up
0
$8.99
Warehouse ?
1
$8.99
Store - Charlottetown ?
0
$8.99
Store - Edmonton ?
1
$8.99
Store - Mississauga ?
0
$8.99
Store - Ottawa ?
This live feed information is to be used as a general guide to current inventory. There is no guarantee of availablility.
FEATURES
  • Weighs only 1 ounce per square yard (28g/m²).
  • An excellent choice for covering weight-sensitive models such as park flyers.
  • Coverlite is heat-sealed to the model, and factory "doped" with a totally fuel proof resin.
  • Stronger and more puncture resistance than normal doped tissue
  • Coverlite can be painted with most model paints.
  • Each sheet measures 36" x 19.5" (915mm x 495)—great for models up to 50"

Coverlite is a super lightweight, extra strong and fuel proof synthetic covering designed to replace tissue and dope coverings.

Balsarite adhesive is required for application.

click image to enlarge
ADDITIONAL PHOTOS
   
VENDOR TECHNOTES
    This is CoverLite Iron-On Orange Synthetic Tissue Covering from Coverite.  
A strong, tough, synthetic material to replace tissue and dope.
++Additional Technical Information Will Be Added As It Becomes Available.++
FEATURES: Ideal for covering light-weight or Park Flyer models.
Extremely light weight of only .89 ounce per square yard (28g per
square meter).
CoverLite is sealed to a model with heat, and is factory "doped" with
a totally fuelproof resin. It is not only resistant to glow and
diesel fuel, but is also airproof and waterproof. Very easy to
apply to a model with Coverite Balsarite or CoverLite Adhesive-
(see COMMENTS).
Stronger and more puncture-resistant than normal doped tissue, and
can be painted with Coverite 21st Century spray paint.
Comes folded in a bag (5"x 5.5") with a hangable header card.
90 day warranty.

INCLUDES: One CoverLite Iron-On Orange Synthetic Tissue Covering
One Instruction Sheet

REQUIRES:-Preapplying CoverLite Adhesive or Fabric Balsarite
onto the surface to be covered, and then applying
heat to tighten the covering.
Miscellaneous covering tools.

SPECS: Length: 36" (915mm)
Width: 19.5" (495mm)
Weight: 1 oz/sq yd (28 g/sq m)

COMMENTS:-The CoverLite Adhesive is not yet available at the time of writing.

Preparation before using CoverLite Covering:
Fill all cracks and hollows. Sand all parts to be covered to
remove bumps or unevenness which would show through the covering.
Wipe away all sanding residues. There are two methods of applying
CoverLite, depending on whether the part being covered is an open
framework or is a solid surface, such as sheet balsa.
Method #1, Open Framework:
With a small piece of plastic sponge apply a very thin coat of
CoverLite Adhesive or Balsarite to the framework. Pay particular
attention to the outer edges (leading and trailing edges are
longerons). Areas of sheet balsa should be coated all over. Allow
the CoverLite Adhesive or Balsarite to dry (15-30 minutes). Cut a
panel of CoverLite at least 1" (25mm) larger all around the frame-
work to be covered and lay the CoverLite on the framework. Set
your iron between 195-212F (90-100C) and tack the Coverlite in
place at a few points around the edges, using the toe of the iron.
While tacking, gently pull the CoverLite to get a smooth fit
without wrinkles. Do not try to get the CoverLite drum tight, just
smooth and wrinkle-free. Reheating and peeling back while hot
allows the CoverLite to be repositioned. Then seal the Coverlite
all around the edges of the frame with the iron. Trim excess from
around the edge with a sharp blade and reseal the deges. Where
panels of CoverLite meet and overlap, the overlap has to be coated
with CoverLite Adhesive or Balsarite (and dried).
so it can be ironed down. It is best to apply this CoverLite
Adhesive or Balsarite with a fine brush BEFORE trimming away the
excess CoverLite.
Method #2, Solid Surfaces:
Solid surfaces such as sheet balsa, ply and veneer. With a scrap
of moistened plastic sponge, apply a thin coat of CoverLite
Adhesive or Balsarite all over the surface to be covered. Cut a
panel of CoverLite oversize and tape it down on a smooth surface
and apply a very thin coat of CoverLite Adhesive or Balsarite.
Allow to dry. Place the coated side of the CoverLite onto the
coated surface and iron down with a cool iron (about 195F, 90C).
Start at the center and iron outward toward the edges to avoid
trapping air under the CoverLite. If the CoverLite wrinkles around
the iron, lower the iron temperature. CoverLite can be contoured
around slight double curves by heating and gently pulling.
For large area of double curvature, it is easiest to cut the
CoverLite into "fingers" which are ironed down in succession.

JAL 3/20/01
ir/jl
Customers who bought this item also bought...
CoverLite Syn Tissue Yellow 19.5" x 36" 
$8.99
  
CoverLite Syn Tissue Red 19.5" x 36" 
$8.99
  
CoverLite Syn Tissue Black 19.5" x 36" 
$8.99
  
CoverLite Syn Tissue Blue 19.5" x 36" 
$8.99
CoverLite Syn Tissue Cream 19.5" x 36" 
$8.99
  
mP-51/SU-26 Motor & Gearbox 
$19.99
  
CoverLite Syn Tissue Silver 19.5" x 36" 
$8.99
  
Silicon Wire Red/Blk 3'@ #18 161-Strand 
$6.99
634202618024 0634202618024 
COVQ1802